URL: https://www.overclockers.at/linux/debian_fstab_mount_problem_168268/page_1 - zur Vollversion wechseln!
hab 2 neue sata platten eingebaut, per cfdisk paritioniert und mit ext3 formatiert. funktioniert soweit auch ganz gut. wenn ich die disks per hand mounte funktionieren sie über samba einwandfrei (ist ein reiner fileserver). allerdings wars das nach dem reboot, denn danach sind sie nicht mehr gemountet (mount -l zeigts nicht an).
fstab:
Code:# /etc/fstab: static file system information. # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc defaults 0 0 /dev/hda1 / ext3 defaults,errors=remount-ro 0 1 /dev/hda2 none swap sw 0 0 /dev/hdc /media/cdrom0 iso9660 ro,user,noauto 0 0 /dev/fd0 /media/floppy0 auto rw,user,noauto 0 0 /dev/sda1 /samba2 ext3 defaults 0 0 /dev/sdb1 /samba3 ext3 defaults 0 0
Code:Jul 2 22:59:54 localhost kernel: SCSI subsystem initialized Jul 2 22:59:54 localhost kernel: libata version 1.02 loaded. Jul 2 22:59:54 localhost kernel: sata_via version 0.20 Jul 2 22:59:54 localhost kernel: ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 177 Jul 2 22:59:54 localhost kernel: sata_via(0000:00:0f.0): routed to hard irq line 11 Jul 2 22:59:54 localhost kernel: ata1: SATA max UDMA/133 cmd 0x9400 ctl 0x9802 bmdma 0xA400 irq 177 Jul 2 22:59:54 localhost kernel: ata2: SATA max UDMA/133 cmd 0x9C00 ctl 0xA002 bmdma 0xA408 irq 177 Jul 2 22:59:54 localhost kernel: ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f Jul 2 22:59:54 localhost kernel: ata1: dev 0 ATA, max UDMA/133, 625142448 sectors: lba48 Jul 2 22:59:54 localhost kernel: ata1: dev 0 configured for UDMA/133 Jul 2 22:59:54 localhost kernel: scsi0 : sata_via Jul 2 22:59:54 localhost kernel: ata2: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f Jul 2 22:59:54 localhost kernel: ata2: dev 0 ATA, max UDMA/133, 625142448 sectors: lba48 Jul 2 22:59:54 localhost kernel: ata2: dev 0 configured for UDMA/133 Jul 2 22:59:54 localhost kernel: scsi1 : sata_via Jul 2 22:59:54 localhost kernel: Vendor: ATA Model: ST3320620AS Rev: 3.AA Jul 2 22:59:54 localhost kernel: Type: Direct-Access ANSI SCSI revision: 05 Jul 2 22:59:54 localhost kernel: Vendor: ATA Model: ST3320620AS Rev: 3.AA Jul 2 22:59:54 localhost kernel: Type: Direct-Access ANSI SCSI revision: 05 Jul 2 22:59:54 localhost kernel: SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB) Jul 2 22:59:54 localhost kernel: SCSI device sda: drive cache: write back Jul 2 22:59:54 localhost kernel: /dev/scsi/host0/bus0/target0/lun0: unknown partition table Jul 2 22:59:54 localhost kernel: Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Jul 2 22:59:54 localhost kernel: SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB) Jul 2 22:59:54 localhost kernel: SCSI device sdb: drive cache: write back Jul 2 22:59:54 localhost kernel: /dev/scsi/host1/bus0/target0/lun0: unknown partition table Jul 2 22:59:54 localhost kernel: Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
Code:server:/var/log# fdisk -l Disk /dev/hda: 200.0 GB, 200049647616 bytes 255 heads, 63 sectors/track, 24321 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/hda1 1 24254 194820223+ 83 Linux /dev/hda2 24255 24321 538177+ 82 Linux swap / Solaris Disk /dev/sda: 320.0 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 1 38913 312568641 83 Linux Disk /dev/sdb: 320.0 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdb1 1 38913 312568641 83 Linux server:/var/log#
Code:Jul 2 22:59:54 localhost kernel: /dev/scsi/host0/bus0/target0/lun0: unknown partition table
hm gut habs mal neu partitioniert und formatiert und der fehler ist weg, allerdings wirds noch immer nicht automatisch gemountet
Code:Jul 3 03:03:00 localhost kernel: sata_via(0000:00:0f.0): routed to hard irq line 11 Jul 3 03:03:00 localhost kernel: ata1: SATA max UDMA/133 cmd 0x9400 ctl 0x9802 bmdma 0xA400 irq 177 Jul 3 03:03:00 localhost kernel: ata2: SATA max UDMA/133 cmd 0x9C00 ctl 0xA002 bmdma 0xA408 irq 177 Jul 3 03:03:00 localhost kernel: ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f Jul 3 03:03:00 localhost kernel: ata1: dev 0 ATA, max UDMA/133, 625142448 sectors: lba48 Jul 3 03:03:00 localhost kernel: ata1: dev 0 configured for UDMA/133 Jul 3 03:03:00 localhost kernel: scsi0 : sata_via Jul 3 03:03:00 localhost kernel: ata2: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f Jul 3 03:03:00 localhost kernel: ata2: dev 0 ATA, max UDMA/133, 625142448 sectors: lba48 Jul 3 03:03:00 localhost kernel: ata2: dev 0 configured for UDMA/133 Jul 3 03:03:00 localhost kernel: scsi1 : sata_via Jul 3 03:03:00 localhost kernel: Vendor: ATA Model: ST3320620AS Rev: 3.AA Jul 3 03:03:00 localhost kernel: Type: Direct-Access ANSI SCSI revision: 05 Jul 3 03:03:00 localhost kernel: SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB) Jul 3 03:03:00 localhost kernel: SCSI device sda: drive cache: write back Jul 3 03:03:00 localhost kernel: /dev/scsi/host0/bus0/target0/lun0: p1 Jul 3 03:03:00 localhost kernel: Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Jul 3 03:03:00 localhost kernel: Vendor: ATA Model: ST3320620AS Rev: 3.AA Jul 3 03:03:00 localhost kernel: Type: Direct-Access ANSI SCSI revision: 05 Jul 3 03:03:00 localhost kernel: SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB) Jul 3 03:03:00 localhost kernel: SCSI device sdb: drive cache: write back Jul 3 03:03:00 localhost kernel: /dev/scsi/host1/bus0/target0/lun0: p1 Jul 3 03:03:00 localhost kernel: Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
Hmm, koenntest du mal (nach einem Reboot) das gesamte Syslog seit dem Bootvorgangsstart plus dem kompletten dmesg-Output nopasten?
syslog
Code:Jul 3 11:30:10 localhost syslogd 1.4.1#17: restart. Jul 3 11:30:10 localhost kernel: klogd 1.4.1#17, log source = /proc/kmsg started. Jul 3 11:30:10 localhost kernel: Inspecting /boot/System.map-2.6.8-2-386 Jul 3 11:30:10 localhost kernel: Loaded 28183 symbols from /boot/System.map-2.6.8-2-386. Jul 3 11:30:10 localhost kernel: Symbols match kernel version 2.6.8. Jul 3 11:30:10 localhost kernel: No module symbols loaded - kernel modules not enabled. Jul 3 11:30:10 localhost kernel: 00000 - 000000001dff0000 (usable) Jul 3 11:30:10 localhost kernel: BIOS-e820: 000000001dff0000 - 000000001dff3000 (ACPI NVS) Jul 3 11:30:10 localhost kernel: BIOS-e820: 000000001dff3000 - 000000001e000000 (ACPI data) Jul 3 11:30:10 localhost kernel: BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) Jul 3 11:30:10 localhost kernel: BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) Jul 3 11:30:10 localhost kernel: BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) Jul 3 11:30:10 localhost kernel: 479MB LOWMEM available. Jul 3 11:30:10 localhost kernel: found SMP MP-table at 000f5bb0 Jul 3 11:30:10 localhost kernel: On node 0 totalpages: 122864 Jul 3 11:30:10 localhost kernel: DMA zone: 4096 pages, LIFO batch:1 Jul 3 11:30:10 localhost kernel: Normal zone: 118768 pages, LIFO batch:16 Jul 3 11:30:10 localhost kernel: HighMem zone: 0 pages, LIFO batch:1 Jul 3 11:30:10 localhost kernel: DMI 2.3 present. Jul 3 11:30:10 localhost kernel: ACPI: RSDP (v000 KM400A ) @ 0x000f7690 Jul 3 11:30:10 localhost kernel: ACPI: RSDT (v001 KM400A AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1dff3040 Jul 3 11:30:10 localhost kernel: ACPI: FADT (v001 KM400A AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1dff30c0 Jul 3 11:30:10 localhost kernel: ACPI: MADT (v001 KM400A AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1dff8040 Jul 3 11:30:10 localhost kernel: ACPI: DSDT (v001 KM400A AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000 Jul 3 11:30:10 localhost kernel: ACPI: PM-Timer IO Port: 0x408 Jul 3 11:30:10 localhost kernel: ACPI: Local APIC address 0xfee00000 Jul 3 11:30:10 localhost kernel: ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Jul 3 11:30:10 localhost kernel: Processor #0 6:3 APIC version 16 Jul 3 11:30:10 localhost kernel: ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) Jul 3 11:30:10 localhost kernel: ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) Jul 3 11:30:10 localhost kernel: IOAPIC[0]: Assigned apic_id 2 Jul 3 11:30:10 localhost kernel: IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23 Jul 3 11:30:10 localhost kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) Jul 3 11:30:10 localhost kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) Jul 3 11:30:10 localhost kernel: ACPI: IRQ0 used by override. Jul 3 11:30:10 localhost kernel: ACPI: IRQ2 used by override. Jul 3 11:30:10 localhost kernel: ACPI: IRQ9 used by override. Jul 3 11:30:10 localhost kernel: Enabling APIC mode: Flat. Using 1 I/O APICs Jul 3 11:30:10 localhost kernel: Using ACPI (MADT) for SMP configuration information Jul 3 11:30:10 localhost kernel: Built 1 zonelists Jul 3 11:30:10 localhost kernel: Kernel command line: root=/dev/hda1 ro Jul 3 11:30:10 localhost kernel: Initializing CPU#0 Jul 3 11:30:10 localhost kernel: PID hash table entries: 2048 (order 11: 16384 bytes) Jul 3 11:30:10 localhost kernel: Detected 799.951 MHz processor. Jul 3 11:30:10 localhost kernel: Using pmtmr for high-res timesource Jul 3 11:30:10 localhost kernel: Console: colour VGA+ 80x25 Jul 3 11:30:10 localhost kernel: Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Jul 3 11:30:10 localhost kernel: Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Jul 3 11:30:10 localhost kernel: Memory: 479676k/491456k available (1337k kernel code, 11008k reserved, 732k data, 204k init, 0k highmem) Jul 3 11:30:10 localhost kernel: Checking if this processor honours the WP bit even in supervisor mode... Ok. Jul 3 11:30:10 localhost kernel: Calibrating delay loop... 1568.76 BogoMIPS Jul 3 11:30:10 localhost kernel: Security Scaffold v1.0.0 initialized Jul 3 11:30:10 localhost kernel: Mount-cache hash table entries: 512 (order: 0, 4096 bytes) Jul 3 11:30:10 localhost kernel: CPU: After generic identify, caps: 0183fbff c1c7fbff 00000000 00000000 Jul 3 11:30:10 localhost kernel: CPU: After vendor identify, caps: 0183fbff c1c7fbff 00000000 00000000 Jul 3 11:30:10 localhost kernel: CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) Jul 3 11:30:10 localhost kernel: CPU: L2 Cache: 64K (64 bytes/line) Jul 3 11:30:10 localhost kernel: CPU: After all inits, caps: 0183fbff c1c7fbff 00000000 00000020 Jul 3 11:30:10 localhost kernel: CPU: AMD Duron(tm) processor stepping 01 Jul 3 11:30:10 localhost kernel: Enabling fast FPU save and restore... done. Jul 3 11:30:10 localhost kernel: Checking 'hlt' instruction... OK. Jul 3 11:30:10 localhost kernel: Checking for popad bug... OK. Jul 3 11:30:10 localhost kernel: enabled ExtINT on CPU#0 Jul 3 11:30:10 localhost kernel: ESR value before enabling vector: 00000000 Jul 3 11:30:10 localhost kernel: ESR value after enabling vector: 00000000 Jul 3 11:30:10 localhost kernel: ENABLING IO-APIC IRQs Jul 3 11:30:10 localhost kernel: init IO_APIC IRQs Jul 3 11:30:10 localhost kernel: IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected. Jul 3 11:30:10 localhost kernel: ..TIMER: vector=0x31 pin1=2 pin2=-1 Jul 3 11:30:10 localhost kernel: Using local APIC timer interrupts. Jul 3 11:30:10 localhost kernel: calibrating APIC timer ... Jul 3 11:30:10 localhost kernel: ..... CPU clock speed is 799.0800 MHz. Jul 3 11:30:10 localhost kernel: ..... host bus clock speed is 199.0950 MHz. Jul 3 11:30:10 localhost kernel: checking if image is initramfs...it isn't (ungzip failed); looks like an initrd Jul 3 11:30:10 localhost kernel: Freeing initrd memory: 4216k freed Jul 3 11:30:10 localhost kernel: NET: Registered protocol family 16 Jul 3 11:30:10 localhost kernel: EISA bus registered Jul 3 11:30:10 localhost kernel: PCI: PCI BIOS revision 2.10 entry at 0xf1550, last bus=1 Jul 3 11:30:10 localhost kernel: PCI: Using configuration type 1 Jul 3 11:30:10 localhost kernel: mtrr: v2.0 (20020519) Jul 3 11:30:10 localhost kernel: ACPI: Subsystem revision 20040326 Jul 3 11:30:10 localhost kernel: ACPI: Interpreter enabled Jul 3 11:30:10 localhost kernel: ACPI: Using IOAPIC for interrupt routing Jul 3 11:30:10 localhost kernel: ACPI: PCI Root Bridge [PCI0] (00:00) Jul 3 11:30:10 localhost kernel: PCI: Probing PCI hardware (bus 00) Jul 3 11:30:10 localhost kernel: ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] Jul 3 11:30:10 localhost kernel: ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12) Jul 3 11:30:10 localhost kernel: ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12) Jul 3 11:30:10 localhost kernel: ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 11 12) *5 Jul 3 11:30:10 localhost kernel: ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *0, disabled. Jul 3 11:30:10 localhost kernel: ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled. Jul 3 11:30:10 localhost kernel: ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled. Jul 3 11:30:10 localhost kernel: ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled. Jul 3 11:30:10 localhost kernel: ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled. Jul 3 11:30:10 localhost kernel: ACPI: PCI Interrupt Link [ALKA] (IRQs *20) Jul 3 11:30:10 localhost kernel: ACPI: PCI Interrupt Link [ALKB] (IRQs *21) Jul 3 11:30:10 localhost kernel: ACPI: PCI Interrupt Link [ALKC] (IRQs *22) Jul 3 11:30:10 localhost kernel: ACPI: PCI Interrupt Link [ALKD] (IRQs *23) Jul 3 11:30:10 localhost kernel: Linux Plug and Play Support v0.97 (c) Adam Belay Jul 3 11:30:10 localhost kernel: PnPBIOS: Scanning system for PnP BIOS support... Jul 3 11:30:10 localhost kernel: PnPBIOS: Found PnP BIOS installation structure at 0xc00fc740 Jul 3 11:30:10 localhost kernel: PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xc770, dseg 0xf0000 Jul 3 11:30:10 localhost kernel: pnp: 00:0b: ioport range 0x3f0-0x3f1 has been reserved Jul 3 11:30:10 localhost kernel: PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver Jul 3 11:30:10 localhost kernel: PCI: Using ACPI for IRQ routing Jul 3 11:30:10 localhost kernel: ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 16 (level, low) -> IRQ 169 Jul 3 11:30:10 localhost kernel: ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20 Jul 3 11:30:10 localhost kernel: ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 177 Jul 3 11:30:10 localhost kernel: ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 177 Jul 3 11:30:10 localhost kernel: ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21 Jul 3 11:30:10 localhost kernel: ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 185 Jul 3 11:30:10 localhost kernel: ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 185 Jul 3 11:30:10 localhost kernel: ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 185 Jul 3 11:30:10 localhost kernel: ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 185 Jul 3 11:30:10 localhost kernel: ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 185 Jul 3 11:30:10 localhost kernel: ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22 Jul 3 11:30:10 localhost kernel: ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 193 Jul 3 11:30:10 localhost kernel: ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23 Jul 3 11:30:10 localhost kernel: ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 201 Jul 3 11:30:10 localhost kernel: ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169 Jul 3 11:30:10 localhost kernel: number of MP IRQ sources: 15. Jul 3 11:30:10 localhost kernel: number of IO-APIC #2 registers: 24. Jul 3 11:30:10 localhost kernel: testing the IO APIC....................... Jul 3 11:30:10 localhost kernel: IO APIC #2...... Jul 3 11:30:10 localhost kernel: .... register #00: 02000000 Jul 3 11:30:10 localhost kernel: ....... : physical APIC id: 02 Jul 3 11:30:10 localhost kernel: ....... : Delivery Type: 0 Jul 3 11:30:10 localhost kernel: ....... : LTS : 0 Jul 3 11:30:10 localhost kernel: .... register #01: 00178003 Jul 3 11:30:10 localhost kernel: ....... : max redirection entries: 0017 Jul 3 11:30:10 localhost kernel: ....... : PRQ implemented: 1 Jul 3 11:30:10 localhost kernel: ....... : IO APIC version: 0003 Jul 3 11:30:10 localhost kernel: .... IRQ redirection table: Jul 3 11:30:10 localhost kernel: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: Jul 3 11:30:10 localhost kernel: 00 000 00 1 0 0 0 0 0 0 00 Jul 3 11:30:10 localhost kernel: 01 001 01 0 0 0 0 0 1 1 39 Jul 3 11:30:10 localhost kernel: 02 001 01 0 0 0 0 0 1 1 31 Jul 3 11:30:10 localhost kernel: 03 001 01 0 0 0 0 0 1 1 41 Jul 3 11:30:10 localhost kernel: 04 001 01 0 0 0 0 0 1 1 49 Jul 3 11:30:10 localhost kernel: 05 001 01 0 0 0 0 0 1 1 51 Jul 3 11:30:10 localhost kernel: 06 001 01 0 0 0 0 0 1 1 59 Jul 3 11:30:10 localhost kernel: 07 001 01 0 0 0 0 0 1 1 61 Jul 3 11:30:10 localhost kernel: 08 001 01 0 0 0 0 0 1 1 69 Jul 3 11:30:10 localhost kernel: 09 001 01 0 1 0 1 0 1 1 71 Jul 3 11:30:10 localhost kernel: 0a 001 01 0 0 0 0 0 1 1 79 Jul 3 11:30:10 localhost kernel: 0b 001 01 0 0 0 0 0 1 1 81 Jul 3 11:30:10 localhost kernel: 0c 001 01 0 0 0 0 0 1 1 89 Jul 3 11:30:10 localhost kernel: 0d 001 01 0 0 0 0 0 1 1 91 Jul 3 11:30:10 localhost kernel: 0e 001 01 0 0 0 0 0 1 1 99 Jul 3 11:30:10 localhost kernel: 0f 001 01 0 0 0 0 0 1 1 A1 Jul 3 11:30:10 localhost kernel: 10 001 01 1 1 0 1 0 1 1 A9 Jul 3 11:30:10 localhost kernel: 11 000 00 1 0 0 0 0 0 0 00 Jul 3 11:30:10 localhost kernel: 12 000 00 1 0 0 0 0 0 0 00 Jul 3 11:30:10 localhost kernel: 13 000 00 1 0 0 0 0 0 0 00 Jul 3 11:30:10 localhost kernel: 14 001 01 1 1 0 1 0 1 1 B1 Jul 3 11:30:10 localhost kernel: 15 001 01 1 1 0 1 0 1 1 B9 Jul 3 11:30:10 localhost kernel: 16 001 01 1 1 0 1 0 1 1 C1 Jul 3 11:30:10 localhost kernel: 17 001 01 1 1 0 1 0 1 1 C9 Jul 3 11:30:10 localhost kernel: Using vector-based indexing Jul 3 11:30:10 localhost kernel: IRQ to pin mappings: Jul 3 11:30:10 localhost kernel: IRQ0 -> 0:2 Jul 3 11:30:10 localhost kernel: IRQ1 -> 0:1 Jul 3 11:30:10 localhost kernel: IRQ3 -> 0:3 Jul 3 11:30:10 localhost kernel: IRQ4 -> 0:4 Jul 3 11:30:10 localhost kernel: IRQ5 -> 0:5 Jul 3 11:30:10 localhost kernel: IRQ6 -> 0:6 Jul 3 11:30:10 localhost kernel: IRQ7 -> 0:7 Jul 3 11:30:10 localhost kernel: IRQ8 -> 0:8 Jul 3 11:30:10 localhost kernel: IRQ9 -> 0:9 Jul 3 11:30:10 localhost kernel: IRQ10 -> 0:10 Jul 3 11:30:10 localhost kernel: IRQ11 -> 0:11 Jul 3 11:30:10 localhost kernel: IRQ12 -> 0:12 Jul 3 11:30:10 localhost kernel: IRQ13 -> 0:13 Jul 3 11:30:10 localhost kernel: IRQ14 -> 0:14 Jul 3 11:30:10 localhost kernel: IRQ15 -> 0:15 Jul 3 11:30:10 localhost kernel: IRQ169 -> 0:16 Jul 3 11:30:10 localhost kernel: IRQ177 -> 0:20 Jul 3 11:30:10 localhost kernel: IRQ185 -> 0:21 Jul 3 11:30:10 localhost kernel: IRQ193 -> 0:22 Jul 3 11:30:10 localhost kernel: IRQ201 -> 0:23 Jul 3 11:30:10 localhost kernel: .................................... done. Jul 3 11:30:10 localhost kernel: VFS: Disk quotas dquot_6.5.1 Jul 3 11:30:10 localhost kernel: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Jul 3 11:30:10 localhost kernel: devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au) Jul 3 11:30:10 localhost kernel: devfs: boot_options: 0x0 Jul 3 11:30:10 localhost kernel: Initializing Cryptographic API Jul 3 11:30:10 localhost kernel: PCI: Via IRQ fixup for 0000:00:10.0, from 10 to 9 Jul 3 11:30:10 localhost kernel: PCI: Via IRQ fixup for 0000:00:10.1, from 10 to 9 Jul 3 11:30:10 localhost kernel: PCI: Via IRQ fixup for 0000:00:10.2, from 11 to 9 Jul 3 11:30:10 localhost kernel: PCI: Via IRQ fixup for 0000:00:10.3, from 11 to 9 Jul 3 11:30:10 localhost kernel: PCI: Via IRQ fixup for 0000:00:11.5, from 5 to 1 Jul 3 11:30:10 localhost kernel: isapnp: Scanning for PnP cards... Jul 3 11:30:10 localhost kernel: isapnp: No Plug & Play device found Jul 3 11:30:10 localhost kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled Jul 3 11:30:10 localhost kernel: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A Jul 3 11:30:10 localhost kernel: RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize Jul 3 11:30:10 localhost kernel: serio: i8042 AUX port at 0x60,0x64 irq 12 Jul 3 11:30:10 localhost kernel: serio: i8042 KBD port at 0x60,0x64 irq 1 Jul 3 11:30:10 localhost kernel: input: AT Translated Set 2 keyboard on isa0060/serio0 Jul 3 11:30:10 localhost kernel: EISA: Probing bus 0 at eisa0 Jul 3 11:30:10 localhost kernel: EISA: Detected 0 cards. Jul 3 11:30:10 localhost kernel: NET: Registered protocol family 2 Jul 3 11:30:10 localhost kernel: IP: routing cache hash table of 4096 buckets, 32Kbytes Jul 3 11:30:10 localhost kernel: TCP: Hash tables configured (established 32768 bind 65536) Jul 3 11:30:10 localhost kernel: NET: Registered protocol family 8 Jul 3 11:30:10 localhost kernel: NET: Registered protocol family 20 Jul 3 11:30:10 localhost kernel: ACPI: (supports S0 S1 S3 S4 S5) Jul 3 11:30:10 localhost kernel: RAMDISK: cramfs filesystem found at block 0 Jul 3 11:30:10 localhost kernel: RAMDISK: Loading 4216 blocks [1 disk] into ram disk... |^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^Hdone. Jul 3 11:30:10 localhost kernel: VFS: Mounted root (cramfs filesystem) readonly. Jul 3 11:30:10 localhost kernel: Freeing unused kernel memory: 204k freed Jul 3 11:30:10 localhost kernel: vesafb: probe of vesafb0 failed with error -6 Jul 3 11:30:10 localhost kernel: NET: Registered protocol family 1 Jul 3 11:30:10 localhost kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 Jul 3 11:30:10 localhost kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Jul 3 11:30:10 localhost kernel: VP_IDE: IDE controller at PCI slot 0000:00:0f.1 Jul 3 11:30:10 localhost kernel: ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 177 Jul 3 11:30:10 localhost kernel: VP_IDE: chipset revision 6 Jul 3 11:30:10 localhost kernel: VP_IDE: not 100%% native mode: will probe irqs later Jul 3 11:30:10 localhost kernel: VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1 Jul 3 11:30:10 localhost kernel: ide0: BM-DMA at 0xac00-0xac07, BIOS settings: hda:DMA, hdb:pio Jul 3 11:30:10 localhost kernel: ide1: BM-DMA at 0xac08-0xac0f, BIOS settings: hdc:pio, hdd:pio Jul 3 11:30:10 localhost kernel: hda: ST3200822A, ATA DISK drive Jul 3 11:30:10 localhost kernel: Using anticipatory io scheduler Jul 3 11:30:10 localhost kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Jul 3 11:30:10 localhost kernel: hda: max request size: 1024KiB Jul 3 11:30:10 localhost kernel: hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63, UDMA(100) Jul 3 11:30:10 localhost kernel: /dev/ide/host0/bus0/target0/lun0: p1 p2 Jul 3 11:30:10 localhost kernel: kjournald starting. Commit interval 5 seconds Jul 3 11:30:10 localhost kernel: EXT3-fs: mounted filesystem with ordered data mode. Jul 3 11:30:10 localhost kernel: Adding 538168k swap on /dev/hda2. Priority:-1 extents:1 Jul 3 11:30:10 localhost kernel: EXT3 FS on hda1, internal journal Jul 3 11:30:10 localhost kernel: Generic RTC Driver v1.07 Jul 3 11:30:10 localhost kernel: Capability LSM initialized Jul 3 11:30:10 localhost kernel: SCSI subsystem initialized Jul 3 11:30:10 localhost kernel: r8169 Gigabit Ethernet driver 1.2 loaded Jul 3 11:30:10 localhost kernel: ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 16 (level, low) -> IRQ 169 Jul 3 11:30:10 localhost kernel: eth0: Identified chip type is 'RTL8169s/8110s'. Jul 3 11:30:10 localhost kernel: eth0: RTL8169 at 0xde820000, 00:02:44:b0:ff:1a, IRQ 169 Jul 3 11:30:10 localhost kernel: eth0: Auto-negotiation Enabled. Jul 3 11:30:10 localhost kernel: eth0: 1000Mbps Full-duplex operation. Jul 3 11:30:10 localhost kernel: via-rhine.c:v1.10-LK1.1.20-2.6 May-23-2004 Written by Donald Becker Jul 3 11:30:10 localhost kernel: ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 201 Jul 3 11:30:10 localhost kernel: eth1: VIA Rhine II at 0xc800, 00:13:d4:55:69:77, IRQ 201. Jul 3 11:30:10 localhost kernel: eth1: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000. Jul 3 11:30:10 localhost kernel: libata version 1.02 loaded. Jul 3 11:30:10 localhost kernel: sata_via version 0.20 Jul 3 11:30:10 localhost kernel: ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 177 Jul 3 11:30:10 localhost kernel: sata_via(0000:00:0f.0): routed to hard irq line 11 Jul 3 11:30:10 localhost kernel: ata1: SATA max UDMA/133 cmd 0x9400 ctl 0x9802 bmdma 0xA400 irq 177 Jul 3 11:30:10 localhost kernel: ata2: SATA max UDMA/133 cmd 0x9C00 ctl 0xA002 bmdma 0xA408 irq 177 Jul 3 11:30:10 localhost kernel: ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f Jul 3 11:30:10 localhost kernel: ata1: dev 0 ATA, max UDMA/133, 625142448 sectors: lba48 Jul 3 11:30:10 localhost kernel: ata1: dev 0 configured for UDMA/133 Jul 3 11:30:10 localhost kernel: scsi0 : sata_via Jul 3 11:30:10 localhost kernel: ata2: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f Jul 3 11:30:10 localhost kernel: ata2: dev 0 ATA, max UDMA/133, 625142448 sectors: lba48 Jul 3 11:30:10 localhost kernel: ata2: dev 0 configured for UDMA/133 Jul 3 11:30:10 localhost kernel: scsi1 : sata_via Jul 3 11:30:10 localhost kernel: Vendor: ATA Model: ST3320620AS Rev: 3.AA Jul 3 11:30:10 localhost kernel: Type: Direct-Access ANSI SCSI revision: 05 Jul 3 11:30:10 localhost kernel: SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB) Jul 3 11:30:10 localhost kernel: SCSI device sda: drive cache: write back Jul 3 11:30:10 localhost kernel: /dev/scsi/host0/bus0/target0/lun0: p1 Jul 3 11:30:10 localhost kernel: Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Jul 3 11:30:10 localhost kernel: Vendor: ATA Model: ST3320620AS Rev: 3.AA Jul 3 11:30:10 localhost kernel: Type: Direct-Access ANSI SCSI revision: 05 Jul 3 11:30:10 localhost kernel: SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB) Jul 3 11:30:10 localhost kernel: SCSI device sdb: drive cache: write back Jul 3 11:30:10 localhost kernel: /dev/scsi/host1/bus0/target0/lun0: p1 Jul 3 11:30:10 localhost kernel: Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0 Jul 3 11:30:10 localhost kernel: Via 686a/8233/8235 audio driver 1.9.1-ac4-2.5 Jul 3 11:30:10 localhost kernel: ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 193 Jul 3 11:30:10 localhost kernel: via82cxxx: Six channel audio available Jul 3 11:30:10 localhost kernel: PCI: Setting latency timer of device 0000:00:11.5 to 64 Jul 3 11:30:10 localhost kernel: ac97_codec: AC97 Audio codec, id: ADS104 (Unknown) Jul 3 11:30:10 localhost kernel: via82cxxx: board #1 at 0xC000, IRQ 193 Jul 3 11:30:10 localhost kernel: usbcore: registered new driver usbfs Jul 3 11:30:10 localhost kernel: usbcore: registered new driver hub Jul 3 11:30:10 localhost kernel: USB Universal Host Controller Interface driver v2.2 Jul 3 11:30:10 localhost kernel: ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 185 Jul 3 11:30:10 localhost kernel: uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller Jul 3 11:30:10 localhost kernel: uhci_hcd 0000:00:10.0: irq 185, io base 0000b000 Jul 3 11:30:10 localhost kernel: uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1 Jul 3 11:30:10 localhost kernel: hub 1-0:1.0: USB hub found Jul 3 11:30:10 localhost kernel: hub 1-0:1.0: 2 ports detected Jul 3 11:30:10 localhost kernel: ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 185 Jul 3 11:30:10 localhost kernel: uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2) Jul 3 11:30:10 localhost kernel: uhci_hcd 0000:00:10.1: irq 185, io base 0000b400 Jul 3 11:30:10 localhost kernel: uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2 Jul 3 11:30:10 localhost kernel: hub 2-0:1.0: USB hub found Jul 3 11:30:10 localhost kernel: hub 2-0:1.0: 2 ports detected Jul 3 11:30:10 localhost kernel: ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 185 Jul 3 11:30:10 localhost kernel: uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3) Jul 3 11:30:10 localhost kernel: uhci_hcd 0000:00:10.2: irq 185, io base 0000b800 Jul 3 11:30:10 localhost kernel: uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3 Jul 3 11:30:10 localhost kernel: hub 3-0:1.0: USB hub found Jul 3 11:30:10 localhost kernel: hub 3-0:1.0: 2 ports detected Jul 3 11:30:10 localhost kernel: ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 185 Jul 3 11:30:10 localhost kernel: uhci_hcd 0000:00:10.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#4) Jul 3 11:30:10 localhost kernel: uhci_hcd 0000:00:10.3: irq 185, io base 0000bc00 Jul 3 11:30:10 localhost kernel: uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4 Jul 3 11:30:10 localhost kernel: hub 4-0:1.0: USB hub found Jul 3 11:30:10 localhost kernel: hub 4-0:1.0: 2 ports detected Jul 3 11:30:10 localhost kernel: ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 185 Jul 3 11:30:10 localhost kernel: ehci_hcd 0000:00:10.4: VIA Technologies, Inc. USB 2.0 Jul 3 11:30:10 localhost kernel: ehci_hcd 0000:00:10.4: irq 185, pci mem de82d000 Jul 3 11:30:10 localhost kernel: ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5 Jul 3 11:30:10 localhost kernel: ehci_hcd 0000:00:10.4: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10 Jul 3 11:30:10 localhost kernel: hub 5-0:1.0: USB hub found Jul 3 11:30:10 localhost kernel: hub 5-0:1.0: 8 ports detected Jul 3 11:30:10 localhost kernel: Linux agpgart interface v0.100 (c) Dave Jones Jul 3 11:30:10 localhost kernel: agpgart: Detected VIA KM400/KM400A chipset Jul 3 11:30:10 localhost kernel: agpgart: Maximum main memory to use for agp memory: 409M Jul 3 11:30:10 localhost kernel: agpgart: AGP aperture is 64M @ 0xe0000000 Jul 3 11:30:10 localhost kernel: cpci_hotplug: CompactPCI Hot Plug Core version: 0.2 Jul 3 11:30:10 localhost kernel: pci_hotplug: PCI Hot Plug PCI Core version: 0.5 Jul 3 11:30:10 localhost kernel: pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5 Jul 3 11:30:10 localhost kernel: pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5 Jul 3 11:30:10 localhost kernel: shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5 Jul 3 11:30:10 localhost kernel: shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5 Jul 3 11:30:10 localhost kernel: input: PC Speaker Jul 3 11:30:10 localhost kernel: inserting floppy driver for 2.6.8-2-386 Jul 3 11:30:10 localhost kernel: Floppy drive(s): fd0 is 1.44M Jul 3 11:30:10 localhost kernel: FDC 0 is a post-1991 82077 Jul 3 11:30:10 localhost kernel: parport: PnPBIOS parport detected. Jul 3 11:30:10 localhost kernel: parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA] Jul 3 11:30:10 localhost kernel: NET: Registered protocol family 17 Jul 3 11:30:12 localhost lpd[2400]: restarted Jul 3 11:30:12 localhost kernel: NET: Registered protocol family 5 Jul 3 11:30:12 localhost atalkd[2410]: restart (2.0.2) Jul 3 11:30:13 localhost atalkd[2410]: zip_getnetinfo for eth0 Jul 3 11:30:33 localhost last message repeated 2 times Jul 3 11:30:43 localhost atalkd[2410]: config for no router Jul 3 11:30:44 localhost atalkd[2410]: ready 0/0/0 Jul 3 11:30:56 localhost papd[2414]: restart (2.0.2) Jul 3 11:30:56 localhost papd[2414]: CUPS support enabled (1.1) Jul 3 11:30:56 localhost afpd[2416]: Registering CNID module [last] Jul 3 11:30:56 localhost afpd[2416]: Registering CNID module [cdb] Jul 3 11:30:56 localhost afpd[2416]: Registering CNID module [dbd] Jul 3 11:30:56 localhost afpd[2416]: Loading ConfigFile Jul 3 11:30:56 localhost afpd[2416]: Finished parsing Config File Jul 3 11:30:57 localhost kernel: NET: Registered protocol family 10 Jul 3 11:30:57 localhost kernel: Disabled Privacy Extensions on device c02cc960(lo) Jul 3 11:30:57 localhost kernel: IPv6 over IPv4 tunneling driver Jul 3 11:30:57 localhost rpc.statd[2451]: Version 1.0.6 Starting Jul 3 11:30:57 localhost rpc.statd[2451]: statd running as root. chown /var/lib/nfs/sm to choose different user Jul 3 11:30:57 localhost /usr/sbin/cron[2456]: (CRON) INFO (pidfile fd = 3) Jul 3 11:30:57 localhost /usr/sbin/cron[2457]: (CRON) STARTUP (fork ok) Jul 3 11:30:58 localhost /usr/sbin/cron[2457]: (CRON) INFO (Running @reboot jobs) Jul 3 11:31:02 localhost afpd[2416]: localhost:AFPServer@* started on 65280.30:128 (2.0.2) Jul 3 11:31:02 localhost afpd[2416]: dsi_tcp: hostname 'server' resolves to loopback address Jul 3 11:31:02 localhost afpd[2416]: dsi_tcp: '192.168.1.8' on interface 'eth0' will be used instead. Jul 3 11:31:02 localhost afpd[2416]: ASIP started on 192.168.1.8:548(5) (2.0.2) Jul 3 11:31:02 localhost afpd[2416]: DSIConfigInit: Error registering afp://192.168.1.8/?NAME=localhost&ZONE= with SRVLOC Jul 3 11:31:02 localhost afpd[2416]: uam: loading (/usr/lib/netatalk/uams_dhx.so) Jul 3 11:31:02 localhost afpd[2416]: uam: uam not found (status=-1) Jul 3 11:31:02 localhost afpd[2416]: uam: loading (/usr/lib/netatalk/uams_clrtxt.so) Jul 3 11:31:02 localhost afpd[2416]: uam: uams_clrtxt.so loaded Jul 3 11:31:02 localhost afpd[2416]: uam: loading (/usr/lib/netatalk/uams_randnum.so) Jul 3 11:31:02 localhost afpd[2416]: uam: uam not found (status=-1) Jul 3 11:31:02 localhost afpd[2416]: uam: "Cleartxt Passwrd" available Jul 3 11:31:07 localhost kernel: eth0: no IPv6 routers present
Code:00000 - 000000001dff0000 (usable) BIOS-e820: 000000001dff0000 - 000000001dff3000 (ACPI NVS) BIOS-e820: 000000001dff3000 - 000000001e000000 (ACPI data) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 479MB LOWMEM available. found SMP MP-table at 000f5bb0 On node 0 totalpages: 122864 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 118768 pages, LIFO batch:16 HighMem zone: 0 pages, LIFO batch:1 DMI 2.3 present. ACPI: RSDP (v000 KM400A ) @ 0x000f7690 ACPI: RSDT (v001 KM400A AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1dff3040 ACPI: FADT (v001 KM400A AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1dff30c0 ACPI: MADT (v001 KM400A AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1dff8040 ACPI: DSDT (v001 KM400A AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000 ACPI: PM-Timer IO Port: 0x408 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 6:3 APIC version 16 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: Assigned apic_id 2 IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Built 1 zonelists Kernel command line: root=/dev/hda1 ro Initializing CPU#0 PID hash table entries: 2048 (order 11: 16384 bytes) Detected 799.951 MHz processor. Using pmtmr for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 479676k/491456k available (1337k kernel code, 11008k reserved, 732k data, 204k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop... 1568.76 BogoMIPS Security Scaffold v1.0.0 initialized Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: 0183fbff c1c7fbff 00000000 00000000 CPU: After vendor identify, caps: 0183fbff c1c7fbff 00000000 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 64K (64 bytes/line) CPU: After all inits, caps: 0183fbff c1c7fbff 00000000 00000020 CPU: AMD Duron(tm) processor stepping 01 Enabling fast FPU save and restore... done. Checking 'hlt' instruction... OK. Checking for popad bug... OK. enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 ENABLING IO-APIC IRQs init IO_APIC IRQs IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected. ..TIMER: vector=0x31 pin1=2 pin2=-1 Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 799.0800 MHz. ..... host bus clock speed is 199.0950 MHz. checking if image is initramfs...it isn't (ungzip failed); looks like an initrd Freeing initrd memory: 4216k freed NET: Registered protocol family 16 EISA bus registered PCI: PCI BIOS revision 2.10 entry at 0xf1550, last bus=1 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20040326 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 11 12) *5 ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [ALKA] (IRQs *20) ACPI: PCI Interrupt Link [ALKB] (IRQs *21) ACPI: PCI Interrupt Link [ALKC] (IRQs *22) ACPI: PCI Interrupt Link [ALKD] (IRQs *23) Linux Plug and Play Support v0.97 (c) Adam Belay PnPBIOS: Scanning system for PnP BIOS support... PnPBIOS: Found PnP BIOS installation structure at 0xc00fc740 PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xc770, dseg 0xf0000 pnp: 00:0b: ioport range 0x3f0-0x3f1 has been reserved PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver PCI: Using ACPI for IRQ routing ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 16 (level, low) -> IRQ 169 ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20 ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 177 ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 177 ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21 ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 185 ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 185 ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 185 ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 185 ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 185 ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22 ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 193 ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23 ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 201 ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169 number of MP IRQ sources: 15. number of IO-APIC #2 registers: 24. testing the IO APIC....................... IO APIC #2...... .... register #00: 02000000 ....... : physical APIC id: 02 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 00178003 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0003 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 001 01 0 0 0 0 0 1 1 39 02 001 01 0 0 0 0 0 1 1 31 03 001 01 0 0 0 0 0 1 1 41 04 001 01 0 0 0 0 0 1 1 49 05 001 01 0 0 0 0 0 1 1 51 06 001 01 0 0 0 0 0 1 1 59 07 001 01 0 0 0 0 0 1 1 61 08 001 01 0 0 0 0 0 1 1 69 09 001 01 0 1 0 1 0 1 1 71 0a 001 01 0 0 0 0 0 1 1 79 0b 001 01 0 0 0 0 0 1 1 81 0c 001 01 0 0 0 0 0 1 1 89 0d 001 01 0 0 0 0 0 1 1 91 0e 001 01 0 0 0 0 0 1 1 99 0f 001 01 0 0 0 0 0 1 1 A1 10 001 01 1 1 0 1 0 1 1 A9 11 000 00 1 0 0 0 0 0 0 00 12 000 00 1 0 0 0 0 0 0 00 13 000 00 1 0 0 0 0 0 0 00 14 001 01 1 1 0 1 0 1 1 B1 15 001 01 1 1 0 1 0 1 1 B9 16 001 01 1 1 0 1 0 1 1 C1 17 001 01 1 1 0 1 0 1 1 C9 Using vector-based indexing IRQ to pin mappings: IRQ0 -> 0:2 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ5 -> 0:5 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:9 IRQ10 -> 0:10 IRQ11 -> 0:11 IRQ12 -> 0:12 IRQ13 -> 0:13 IRQ14 -> 0:14 IRQ15 -> 0:15 IRQ169 -> 0:16 IRQ177 -> 0:20 IRQ185 -> 0:21 IRQ193 -> 0:22 IRQ201 -> 0:23 .................................... done. VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x0 Initializing Cryptographic API PCI: Via IRQ fixup for 0000:00:10.0, from 10 to 9 PCI: Via IRQ fixup for 0000:00:10.1, from 10 to 9 PCI: Via IRQ fixup for 0000:00:10.2, from 11 to 9 PCI: Via IRQ fixup for 0000:00:10.3, from 11 to 9 PCI: Via IRQ fixup for 0000:00:11.5, from 5 to 1 isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 input: AT Translated Set 2 keyboard on isa0060/serio0 EISA: Probing bus 0 at eisa0 EISA: Detected 0 cards. NET: Registered protocol family 2 IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 65536) NET: Registered protocol family 8 NET: Registered protocol family 20 ACPI: (supports S0 S1 S3 S4 S5) RAMDISK: cramfs filesystem found at block 0 RAMDISK: Loading 4216 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\done. VFS: Mounted root (cramfs filesystem) readonly. Freeing unused kernel memory: 204k freed vesafb: probe of vesafb0 failed with error -6 NET: Registered protocol family 1 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:0f.1 ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 177 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1 ide0: BM-DMA at 0xac00-0xac07, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xac08-0xac0f, BIOS settings: hdc:pio, hdd:pio hda: ST3200822A, ATA DISK drive Using anticipatory io scheduler ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hda: max request size: 1024KiB hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63, UDMA(100) /dev/ide/host0/bus0/target0/lun0: p1 p2 kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. Adding 538168k swap on /dev/hda2. Priority:-1 extents:1 EXT3 FS on hda1, internal journal Generic RTC Driver v1.07 Capability LSM initialized SCSI subsystem initialized r8169 Gigabit Ethernet driver 1.2 loaded ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 16 (level, low) -> IRQ 169 eth0: Identified chip type is 'RTL8169s/8110s'. eth0: RTL8169 at 0xde820000, 00:02:44:b0:ff:1a, IRQ 169 eth0: Auto-negotiation Enabled. eth0: 1000Mbps Full-duplex operation. via-rhine.c:v1.10-LK1.1.20-2.6 May-23-2004 Written by Donald Becker ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 201 eth1: VIA Rhine II at 0xc800, 00:13:d4:55:69:77, IRQ 201. eth1: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000. libata version 1.02 loaded. sata_via version 0.20 ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 177 sata_via(0000:00:0f.0): routed to hard irq line 11 ata1: SATA max UDMA/133 cmd 0x9400 ctl 0x9802 bmdma 0xA400 irq 177 ata2: SATA max UDMA/133 cmd 0x9C00 ctl 0xA002 bmdma 0xA408 irq 177 ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f ata1: dev 0 ATA, max UDMA/133, 625142448 sectors: lba48 ata1: dev 0 configured for UDMA/133 scsi0 : sata_via ata2: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f ata2: dev 0 ATA, max UDMA/133, 625142448 sectors: lba48 ata2: dev 0 configured for UDMA/133 scsi1 : sata_via Vendor: ATA Model: ST3320620AS Rev: 3.AA Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB) SCSI device sda: drive cache: write back /dev/scsi/host0/bus0/target0/lun0: p1 Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Vendor: ATA Model: ST3320620AS Rev: 3.AA Type: Direct-Access ANSI SCSI revision: 05 SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB) SCSI device sdb: drive cache: write back /dev/scsi/host1/bus0/target0/lun0: p1 Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0 Via 686a/8233/8235 audio driver 1.9.1-ac4-2.5 ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 193 via82cxxx: Six channel audio available PCI: Setting latency timer of device 0000:00:11.5 to 64 ac97_codec: AC97 Audio codec, id: ADS104 (Unknown) via82cxxx: board #1 at 0xC000, IRQ 193 usbcore: registered new driver usbfs usbcore: registered new driver hub USB Universal Host Controller Interface driver v2.2 ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 185 uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller uhci_hcd 0000:00:10.0: irq 185, io base 0000b000 uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 185 uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2) uhci_hcd 0000:00:10.1: irq 185, io base 0000b400 uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 185 uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3) uhci_hcd 0000:00:10.2: irq 185, io base 0000b800 uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 185 uhci_hcd 0000:00:10.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#4) uhci_hcd 0000:00:10.3: irq 185, io base 0000bc00 uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 185 ehci_hcd 0000:00:10.4: VIA Technologies, Inc. USB 2.0 ehci_hcd 0000:00:10.4: irq 185, pci mem de82d000 ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5 ehci_hcd 0000:00:10.4: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10 hub 5-0:1.0: USB hub found hub 5-0:1.0: 8 ports detected Linux agpgart interface v0.100 (c) Dave Jones agpgart: Detected VIA KM400/KM400A chipset agpgart: Maximum main memory to use for agp memory: 409M agpgart: AGP aperture is 64M @ 0xe0000000 cpci_hotplug: CompactPCI Hot Plug Core version: 0.2 pci_hotplug: PCI Hot Plug PCI Core version: 0.5 pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5 pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5 shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5 shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5 input: PC Speaker inserting floppy driver for 2.6.8-2-386 Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 parport: PnPBIOS parport detected. parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA] NET: Registered protocol family 17
Code:# /etc/fstab: static file system information. # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc defaults 0 0 /dev/hda1 / ext3 defaults,errors=remount-ro 0 1 /dev/hda2 none swap sw 0 0 /dev/hdc /media/cdrom0 iso9660 ro,user,noauto 0 0 /dev/fd0 /media/floppy0 auto rw,user,noauto 0 0 /dev/sda1 /samba/storage2 ext3 defaults 0 0 /dev/sdb1 /samba/storage3 ext3 defaults 0 0
Code:Disk /dev/hda: 200.0 GB, 200049647616 bytes 255 heads, 63 sectors/track, 24321 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/hda1 1 24254 194820223+ 83 Linux /dev/hda2 24255 24321 538177+ 82 Linux swap / Solaris Disk /dev/sda: 320.0 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 1 38913 312568641 83 Linux Disk /dev/sdb: 320.0 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdb1 1 38913 312568641 83 Linux
Code:/dev/hda1 on / type ext3 (rw,errors=remount-ro) [/] proc on /proc type proc (rw) sysfs on /sys type sysfs (rw) devpts on /dev/pts type devpts (rw,gid=5,mode=620) tmpfs on /dev/shm type tmpfs (rw) usbfs on /proc/bus/usb type usbfs (rw)
wennst "mount -a" eingibst, werdens dann gemounted oder auch nicht?
ja, werden dann gemountet
als schlampige lösung würde ich einfach irgendwo eine eigene datei erstellen und diese zum jeweiligen runlevel hinzufügen mit dem befehl "mount -a". Unter gentoo gibts z.B eine local.start wo du sowas reinschreiben kannst. Ist aber eine absolute quick&dirty lösung, aber was anderes fällt mir auch grad ned ein
mhm, ist sicher eine möglichkeit allerdings hätt ich kein gutes gefühl dabei 
andere vorschläge?
Bin mir nicht sicher ob das geht, aber du könntest einfach in der /etc/fstab einen anderen parameter eingeben statt default, auto zb, bin mir aber nicht sicher, welche es da gibt, man fstab verweist auf man mount und dort find ich nix passendes, vllt gibts eine option onboot oder wwi, aber wenn ers erkennt und du musst es selber mounten hört sich das nach dem an.
hth
overclockers.at v4.thecommunity
© all rights reserved by overclockers.at 2000-2025