URL: https://www.overclockers.at/linux/externe_hdd_wird_nicht_mehr_eingebunden_debian_199132/page_1 - zur Vollversion wechseln!
Servus....^^
hätte folgendes Problem:
nachdem meine IDE Platte eingegangen ist hab ich erfolgreich das komplette System auf die neue HDD "gecloned" und kann damit auch starten usw...
Jedoch hab ich zur Zeit ein Problem mit einer externen 2,5" HDD, welche per USB 2.0 eingebunden wird. Die HDD wird zwar erkannt aber nachdem folgende Meldung kommt:
usb-storage: device scan complete
wird die HDD nicht zum Beispiel als sda angegeben.
Somit ist auch kein Zugriff möglich.
Wenn ich jedoch das System mit Ubuntu oder ähnliches boote, wird problemlos die externe Festplatte erkannt.
Hättet ihr Lösungsvorschläge?
Danke!
Vor 2 Tagen oder so hat das jedoch alles problemlos funktioniert!
Code:usb 4-4: new high speed USB device using ehci_hcd and address 5 usb 4-4: configuration #1 chosen from 1 choice scsi1 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 5 usb-storage: waiting for device to settle before scanning Vendor: Hitachi Model: HTS541616J9SA00 Rev: Type: Direct-Access ANSI SCSI revision: 02 usb-storage: device scan complete
was sagt:
Code:modproble -l *usb* ; modprobe l *hci*
bitte komplettCode:dmesg
Code:ls /dev/[hs]d[a-z]
Code:modprobe -l *usb* ; modprobe -l *hci* /lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/dvb-usb/dvb-usb-dtt200u.ko /lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/dvb-usb/dvb-usb-dibusb-mb.ko /lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/dvb-usb/dvb-usb-digitv.ko /lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/dvb-usb/dvb-usb-dibusb-mc.ko /lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/dvb-usb/dvb-usb-dibusb-common.ko /lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/dvb-usb/dvb-usb-vp702x.ko /lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/dvb-usb/dvb-usb.ko /lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/dvb-usb/dvb-usb-nova-t-usb2.ko /lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/dvb-usb/dvb-usb-a800.ko /lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/dvb-usb/dvb-usb-vp7045.ko /lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/dvb-usb/dvb-usb-cxusb.ko /lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/dvb-usb/dvb-usb-gp8psk.ko /lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/dvb-usb/dvb-usb-umt-010.ko /lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/b2c2/b2c2-flexcop-usb.ko /lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/ttusb-dec/ttusb_dec.ko /lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/ttusb-dec/ttusbdecfe.ko /lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/ttusb-budget/dvb-ttusb-budget.ko /lib/modules/2.6.18-6-686/kernel/drivers/media/video/pvrusb2/pvrusb2.ko /lib/modules/2.6.18-6-686/kernel/drivers/media/video/usbvideo/usbvideo.ko /lib/modules/2.6.18-6-686/kernel/drivers/media/video/cpia_usb.ko /lib/modules/2.6.18-6-686/kernel/drivers/isdn/gigaset/usb_gigaset.ko /lib/modules/2.6.18-6-686/kernel/drivers/isdn/hisax/hfc_usb.ko /lib/modules/2.6.18-6-686/kernel/drivers/usb/core/usbcore.ko /lib/modules/2.6.18-6-686/kernel/drivers/usb/atm/xusbatm.ko /lib/modules/2.6.18-6-686/kernel/drivers/usb/atm/usbatm.ko /lib/modules/2.6.18-6-686/kernel/drivers/usb/class/usblp.ko /lib/modules/2.6.18-6-686/kernel/drivers/usb/storage/usb-storage.ko /lib/modules/2.6.18-6-686/kernel/drivers/usb/misc/usbled.ko /lib/modules/2.6.18-6-686/kernel/drivers/usb/misc/sisusbvga/sisusbvga.ko /lib/modules/2.6.18-6-686/kernel/drivers/usb/misc/usbtest.ko /lib/modules/2.6.18-6-686/kernel/drivers/usb/misc/usblcd.ko /lib/modules/2.6.18-6-686/kernel/drivers/usb/misc/legousbtower.ko /lib/modules/2.6.18-6-686/kernel/drivers/usb/misc/ldusb.ko /lib/modules/2.6.18-6-686/kernel/drivers/usb/net/plusb.ko /lib/modules/2.6.18-6-686/kernel/drivers/usb/net/usbnet.ko /lib/modules/2.6.18-6-686/kernel/drivers/usb/serial/ir-usb.ko /lib/modules/2.6.18-6-686/kernel/drivers/usb/serial/ti_usb_3410_5052.ko /lib/modules/2.6.18-6-686/kernel/drivers/usb/serial/kl5kusb105.ko /lib/modules/2.6.18-6-686/kernel/drivers/usb/serial/usbserial.ko /lib/modules/2.6.18-6-686/kernel/drivers/usb/input/usbmouse.ko /lib/modules/2.6.18-6-686/kernel/drivers/usb/input/usbkbd.ko /lib/modules/2.6.18-6-686/kernel/drivers/usb/input/usbhid.ko /lib/modules/2.6.18-6-686/kernel/drivers/usb/input/usbtouchscreen.ko /lib/modules/2.6.18-6-686/kernel/drivers/usb/mon/usbmon.ko /lib/modules/2.6.18-6-686/kernel/drivers/net/irda/irda-usb.ko /lib/modules/2.6.18-6-686/kernel/drivers/char/watchdog/pcwd_usb.ko /lib/modules/2.6.18-6-686/kernel/drivers/bluetooth/hci_usb.ko /lib/modules/2.6.18-6-686/kernel/drivers/bluetooth/bfusb.ko /lib/modules/2.6.18-6-686/kernel/sound/usb/snd-usb-lib.ko /lib/modules/2.6.18-6-686/kernel/sound/usb/usx2y/snd-usb-usx2y.ko /lib/modules/2.6.18-6-686/kernel/sound/usb/snd-usb-audio.ko /lib/modules/2.6.18-6-686/kernel/drivers/ieee1394/ohci1394.ko /lib/modules/2.6.18-6-686/kernel/drivers/scsi/ahci.ko /lib/modules/2.6.18-6-686/kernel/drivers/usb/host/ehci-hcd.ko /lib/modules/2.6.18-6-686/kernel/drivers/usb/host/ohci-hcd.ko /lib/modules/2.6.18-6-686/kernel/drivers/usb/host/uhci-hcd.ko /lib/modules/2.6.18-6-686/kernel/drivers/bluetooth/hci_vhci.ko /lib/modules/2.6.18-6-686/kernel/drivers/bluetooth/hci_usb.ko /lib/modules/2.6.18-6-686/kernel/drivers/bluetooth/hci_uart.ko /lib/modules/2.6.18-6-686/kernel/drivers/mmc/sdhci.ko
Code:dmesg Linux version 2.6.18-6-686 (Debian 2.6.18.dfsg.1-22etch2) (dannf@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Mon Aug 18 08:42:39 UTC 2008 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003ff40000 (usable) BIOS-e820: 000000003ff40000 - 000000003ff50000 (ACPI data) BIOS-e820: 000000003ff50000 - 0000000040000000 (ACPI NVS) 127MB HIGHMEM available. 896MB LOWMEM available. On node 0 totalpages: 261952 DMA zone: 4096 pages, LIFO batch:0 Normal zone: 225280 pages, LIFO batch:31 HighMem zone: 32576 pages, LIFO batch:7 DMI 2.3 present. ACPI: RSDP (v000 ACPIAM ) @ 0x000f5db0 ACPI: RSDT (v001 A M I OEMRSDT 0x05000406 MSFT 0x00000097) @ 0x3ff40000 ACPI: FADT (v001 A M I OEMFACP 0x05000406 MSFT 0x00000097) @ 0x3ff40200 ACPI: OEMB (v001 A M I OEMBIOS 0x05000406 MSFT 0x00000097) @ 0x3ff50040 ACPI: DSDT (v001 1ABSP 1ABSP001 0x00000001 MSFT 0x02000001) @ 0x00000000 ACPI: PM-Timer IO Port: 0x408 Allocating PCI resources starting at 50000000 (gap: 40000000:c0000000) Detected 1500.093 MHz processor. Built 1 zonelists. Total pages: 261952 Kernel command line: root=/dev/hda3 ro Found and enabled local APIC! mapped APIC to ffffd000 (fee00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1030676k/1047808k available (1541k kernel code, 16456k reserved, 580k data, 196k init, 130304k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 3002.22 BogoMIPS (lpj=6004456) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Capability LSM initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: a7e9fbbf 00000000 00000000 00000000 00000180 00000000 00000000 CPU: After vendor identify, caps: a7e9fbbf 00000000 00000000 00000000 00000180 00000000 00000000 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 1024K CPU: After all inits, caps: a7e9fbbf 00000000 00000000 00000040 00000180 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 12k freed ACPI: Core revision 20060707 ACPI: setting ELCR to 0200 (from 0e30) CPU0: Intel(R) Pentium(R) M processor 1500MHz stepping 05 SMP motherboard not detected. Brought up 1 CPUs migration_cost=0 checking if image is initramfs... it is Freeing initrd memory: 4786k freed NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2 PCI: Using configuration type 1 Setting up standard PCI resources ACPI Error (evregion-0317): No handler for Region [ECOR] (c18ef63c) [EmbeddedControl] [20060707] ACPI Error (exfldio-0290): Region EmbeddedControl(3) has no handler [20060707] ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.SBRG.EC0_.ACS_] (Node c18f4f40), AE_NOT_EXIST ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.AC__._INI] (Node c18f4c34), AE_NOT_EXIST ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) ACPI Error (evregion-0317): No handler for Region [ECOR] (c18ef63c) [EmbeddedControl] [20060707] ACPI Error (exfldio-0290): Region EmbeddedControl(3) has no handler [20060707] ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.SBRG.EC0_.BATS] (Node c18f4f2c), AE_NOT_EXIST ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.BAT0._STA] (Node c18f7414), AE_NOT_EXIST ACPI Error (uteval-0212): Method execution failed [\_SB_.BAT0._STA] (Node c18f7414), AE_NOT_EXIST PCI quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO PCI quirk: region 0500-053f claimed by ICH4 GPIO PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 Boot video device is 0000:01:00.0 PCI: Transparent bridge - 0000:00:1e.0 PCI: Bus #03 (-#06) is hidden behind transparent bridge #02 (-#02) (try 'pci=assign-busses') Please report the result to linux-kernel to fix this permanently PCI: Bus #07 (-#0a) is hidden behind transparent bridge #02 (-#02) (try 'pci=assign-busses') Please report the result to linux-kernel to fix this permanently ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: Embedded Controller [EC0] (gpe 28) interrupt mode. ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 *4 5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 15 devices PnPBIOS: Disabled by ACPI PNP PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: 00:09: ioport range 0x480-0x48f has been reserved pnp: 00:09: ioport range 0x5c0-0x5cf has been reserved pnp: 00:0d: ioport range 0x540-0x55f has been reserved pnp: 00:0d: ioport range 0x400-0x47f could not be reserved pnp: 00:0d: ioport range 0x480-0x48f has been reserved pnp: 00:0d: ioport range 0x500-0x53f has been reserved pnp: 00:0d: ioport range 0x4c0-0x4cf has been reserved PCI: Bridge: 0000:00:01.0 IO window: d000-dfff MEM window: ff800000-ff8fffff PREFETCH window: ce900000-de9fffff PCI: Bus 3, cardbus bridge: 0000:02:01.0 IO window: 00001000-000010ff IO window: 00001400-000014ff PREFETCH window: 52000000-53ffffff MEM window: 54000000-55ffffff PCI: Bus 7, cardbus bridge: 0000:02:01.1 IO window: 00001800-000018ff IO window: 00001c00-00001cff PREFETCH window: 56000000-57ffffff MEM window: 58000000-59ffffff PCI: Bridge: 0000:00:1e.0 IO window: 1000-1fff MEM window: ff900000-ff9fffff PREFETCH window: dea00000-deafffff PCI: Enabling device 0000:00:1e.0 (0106 -> 0107) PCI: Setting latency timer of device 0000:00:1e.0 to 64 PCI: Enabling device 0000:02:01.0 (0000 -> 0003) ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 4 PCI: setting IRQ 4 as level-triggered ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [LNKB] -> GSI 4 (level, low) -> IRQ 4 PCI: Setting latency timer of device 0000:02:01.0 to 64 ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:02:01.1[B] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:02:01.1 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered audit: initializing netlink socket (disabled) audit(1220242074.016:1): initialized highmem bounce pool size: 64 pages VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 4 (level, low) -> IRQ 4 ACPI: PCI interrupt for device 0000:00:1f.6 disabled RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize PNP: PS/2 Controller [PNP0303:PS2K,PNP0f12:PS2M] at 0x60,0x64 irq 1,12 i8042.c: Detected active multiplexing controller, rev 1.1. serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 serio: i8042 AUX3 port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 8 NET: Registered protocol family 20 Using IPI No-Shortcut mode ACPI: (supports S0 S3 S4 S5) Freeing unused kernel memory: 196k freed Time: tsc clocksource has been installed. ACPI: Invalid PBLK length [7] ACPI: CPU0 (power states: C1[C1] C2[C2]) ACPI: Thermal Zone [THRM] (59 C) input: AT Translated Set 2 keyboard as /class/input/input0 usbcore: registered new driver usbfs usbcore: registered new driver hub USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1d.0: irq 11, io base 0x0000e800 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5 PCI: setting IRQ 5 as level-triggered ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.1: irq 5, io base 0x0000e880 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ieee1394: Initialized config rom entry `ip1394' ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 9 PCI: setting IRQ 9 as level-triggered ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 9 (level, low) -> IRQ 9 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.2: irq 9, io base 0x0000ec00 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected Time: acpi_pm clocksource has been installed. ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10 PCI: setting IRQ 10 as level-triggered ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4 ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 10, io mem 0xffaffc00 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 6 ports detected usb 1-1: new full speed USB device using uhci_hcd and address 2 ICH4: IDE controller at PCI slot 0000:00:1f.1 PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 9 (level, low) -> IRQ 9 ICH4: chipset revision 3 ICH4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... usb 4-1: new high speed USB device using ehci_hcd and address 2 hda: ST960815A, ATA DISK drive usb 4-1: configuration #1 chosen from 1 choice SCSI subsystem initialized Initializing USB Mass Storage driver... scsi0 : SCSI emulation for USB Mass Storage devices usbcore: registered new driver usb-storage USB Mass Storage support registered. usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: TOSHIBA DVD-ROM SD-R6112, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 tg3.c:v3.65 (August 07, 2006) ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKB] -> GSI 4 (level, low) -> IRQ 4 eth0: Tigon3 [partno(BCM95788A50) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000BaseT Ethernet 00:0e:a6:aa:1b:94 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[0] TSOcap[1] eth0: dma_rwctrl[763f0000] dma_mask[32-bit] ACPI: PCI Interrupt 0000:02:01.2[C] -> Link [LNKC] -> GSI 9 (level, low) -> IRQ 9 ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[9] MMIO=[ff9ef800-ff9effff] Max Packet=[2048] IR/IT contexts=[4/4] hda: max request size: 512KiB hda: 117210240 sectors (60011 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 hda3 hda4 hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 Attempting manual resume kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e018000318798f] Adding 2048276k swap on /dev/hda2. Priority:-1 extents:1 across:2048276k EXT3 FS on hda3, internal journal Vendor: Hitachi Model: HTS541616J9SA00 Rev: Type: Direct-Access ANSI SCSI revision: 02 usb-storage: device scan complete ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1) ieee1394: sbp2: Try serialize_io=0 for better performance ath_hal: module license 'Proprietary' taints kernel. ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) wlan: 0.8.4.2 (0.9.3) ath_rate_sample: 1.2 (0.9.3) ath_pci: 0.9.4.5 (0.9.3) ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNKB] -> GSI 4 (level, low) -> IRQ 4 wifi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps wifi0: turboA rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps wifi0: H/W encryption support: WEP AES AES_CCM TKIP wifi0: mac 5.9 phy 4.3 radio 3.6 wifi0: Use hw queue 1 for WME_AC_BE traffic wifi0: Use hw queue 0 for WME_AC_BK traffic wifi0: Use hw queue 2 for WME_AC_VI traffic wifi0: Use hw queue 3 for WME_AC_VO traffic wifi0: Use hw queue 8 for CAB traffic wifi0: Use hw queue 9 for beacons wifi0: Atheros 5212: mem=0xff9d0000, irq=4 device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: [email]dm-devel@redhat.com[/email] ACPI: Battery Slot [BAT0] (battery absent) ACPI: Battery Slot [BAT1] (battery absent) ACPI: AC Adapter [AC] (on-line) ACPI: Power Button (FF) [PWRF] ACPI: Lid Switch [LID] ACPI: Sleep Button (CM) [SLPB] ACPI: Power Button (CM) [PWRB] parport: PnPBIOS parport detected. parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA] lp0: using parport0 (interrupt-driven). ppdev: user-space parallel port driver PM: Writing back config space on device 0000:02:00.0 at offset b (was 3ed173b, writing 17351043) PM: Writing back config space on device 0000:02:00.0 at offset 3 (was 0, writing 4010) PM: Writing back config space on device 0000:02:00.0 at offset 2 (was 2000000, writing 2000003) PM: Writing back config space on device 0000:02:00.0 at offset 1 (was 2b00000, writing 2b00106) PM: Writing back config space on device 0000:02:00.0 at offset 0 (was 3ed173b, writing 169c14e4) tg3: eth0: Link is up at 100 Mbps, full duplex. tg3: eth0: Flow control is on for TX and on for RX. Installing knfsd (copyright (C) 1996 [email]okir@monad.swb.de[/email]). NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory NFSD: starting 90-second grace period Linux agpgart interface v0.101 (c) Dave Jones [drm] Initialized drm 1.0.1 20051102 ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 [drm] Initialized radeon 1.25.0 20060524 on minor 0 Bluetooth: Core ver 2.10 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP ver 2.8 Bluetooth: L2CAP socket layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM ver 1.8 mtrr: 0xd0000000,0x8000000 overlaps existing 0xd0000000,0x4000000 mtrr: 0xd0000000,0x8000000 overlaps existing 0xd0000000,0x4000000 mtrr: 0xd0000000,0x8000000 overlaps existing 0xd0000000,0x4000000 [drm:radeon_cp_init] *ERROR* radeon_cp_init called without lock held [drm:drm_unlock] *ERROR* Process 2315 using kernel context 0 usb 4-1: USB disconnect, address 2 usb 2-1: new full speed USB device using uhci_hcd and address 2 usb 2-1: device descriptor read/64, error -71 usb 2-1: device descriptor read/64, error -71 usb 2-1: new full speed USB device using uhci_hcd and address 3 usb 2-1: device descriptor read/64, error -71 usb 2-1: device descriptor read/64, error -71 usb 2-1: new full speed USB device using uhci_hcd and address 4 usb 2-1: device not accepting address 4, error -71 usb 2-1: new full speed USB device using uhci_hcd and address 5 usb 2-1: device not accepting address 5, error -71 usb 2-1: new full speed USB device using uhci_hcd and address 6 usb 2-1: device descriptor read/64, error -71 usb 2-1: device descriptor read/64, error -71 usb 2-1: new full speed USB device using uhci_hcd and address 7 usb 2-1: device descriptor read/64, error -71 usb 2-1: device descriptor read/64, error -71 usb 2-1: new full speed USB device using uhci_hcd and address 8 usb 2-1: device not accepting address 8, error -71 usb 2-1: new full speed USB device using uhci_hcd and address 9 usb 2-1: device not accepting address 9, error -71 usb 4-4: new high speed USB device using ehci_hcd and address 5 usb 4-4: configuration #1 chosen from 1 choice scsi1 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 5 usb-storage: waiting for device to settle before scanning Vendor: Hitachi Model: HTS541616J9SA00 Rev: Type: Direct-Access ANSI SCSI revision: 02 usb-storage: device scan complete usb 4-4: USB disconnect, address 5 usb 4-4: new high speed USB device using ehci_hcd and address 6 usb 4-4: configuration #1 chosen from 1 choice scsi2 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 6 usb-storage: waiting for device to settle before scanning Vendor: Hitachi Model: HTS541616J9SA00 Rev: Type: Direct-Access ANSI SCSI revision: 02 usb-storage: device scan complete usb 4-4: USB disconnect, address 6 usb 4-3: new high speed USB device using ehci_hcd and address 7 usb 4-3: configuration #1 chosen from 1 choice scsi3 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 7 usb-storage: waiting for device to settle before scanning Vendor: Hitachi Model: HTS541616J9SA00 Rev: Type: Direct-Access ANSI SCSI revision: 02 usb-storage: device scan complete usb 4-3: USB disconnect, address 7 usb 4-1: new high speed USB device using ehci_hcd and address 8 usb 4-1: configuration #1 chosen from 1 choice [B]scsi4 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 8 usb-storage: waiting for device to settle before scanning Vendor: Hitachi Model: HTS541616J9SA00 Rev: Type: Direct-Access ANSI SCSI revision: 02 usb-storage: device scan complete [/B] usb 4-1: USB disconnect, address 8 usb 4-3: new high speed USB device using ehci_hcd and address 9 usb 4-3: configuration #1 chosen from 1 choice scsi5 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 9 usb-storage: waiting for device to settle before scanning Vendor: Hitachi Model: HTS541616J9SA00 Rev: Type: Direct-Access ANSI SCSI revision: 02 usb-storage: device scan complete usb 4-2: new high speed USB device using ehci_hcd and address 15 usb 4-2: new high speed USB device using ehci_hcd and address 19 usb 4-2: new high speed USB device using ehci_hcd and address 29 usb 4-2: new high speed USB device using ehci_hcd and address 33 usb 4-2: new high speed USB device using ehci_hcd and address 36 usb 4-2: new high speed USB device using ehci_hcd and address 42 ehci_hcd 0000:00:1d.7: port 2 reset error -110 hub 4-0:1.0: hub_port_status failed (err = -32) usb 4-2: new high speed USB device using ehci_hcd and address 54 ehci_hcd 0000:00:1d.7: port 2 reset error -110 hub 4-0:1.0: hub_port_status failed (err = -32) usb 4-2: new high speed USB device using ehci_hcd and address 65 usb 4-2: new high speed USB device using ehci_hcd and address 69 ehci_hcd 0000:00:1d.7: port 2 reset error -110 hub 4-0:1.0: hub_port_status failed (err = -32) ehci_hcd 0000:00:1d.7: port 2 reset error -110 hub 4-0:1.0: hub_port_status failed (err = -32) hub 4-0:1.0: Cannot enable port 2. Maybe the USB cable is bad? usb 4-2: new high speed USB device using ehci_hcd and address 76 usb 4-2: new high speed USB device using ehci_hcd and address 99 usb 4-2: new high speed USB device using ehci_hcd and address 111 usb 4-2: new high speed USB device using ehci_hcd and address 118 usb 4-2: new high speed USB device using ehci_hcd and address 121 usb 4-2: new high speed USB device using ehci_hcd and address 8 usb 4-2: new high speed USB device using ehci_hcd and address 10 usb 4-2: new high speed USB device using ehci_hcd and address 11 ehci_hcd 0000:00:1d.7: port 2 reset error -110 hub 4-0:1.0: hub_port_status failed (err = -32) usb 4-2: new high speed USB device using ehci_hcd and address 14 usb 4-2: new high speed USB device using ehci_hcd and address 27 usb 4-2: new high speed USB device using ehci_hcd and address 49 usb 4-2: new high speed USB device using ehci_hcd and address 56 usb 4-2: new high speed USB device using ehci_hcd and address 64 usb 4-2: new high speed USB device using ehci_hcd and address 69 usb 4-2: new high speed USB device using ehci_hcd and address 75 usb 4-2: new high speed USB device using ehci_hcd and address 76 usb 4-2: new high speed USB device using ehci_hcd and address 97 ehci_hcd 0000:00:1d.7: port 2 reset error -110 hub 4-0:1.0: hub_port_status failed (err = -32) usb 4-2: new high speed USB device using ehci_hcd and address 100 hub 4-0:1.0: Cannot enable port 2. Maybe the USB cable is bad? usb 4-2: new high speed USB device using ehci_hcd and address 101 usb 4-2: configuration #1 chosen from 1 choice scsi6 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 101 usb-storage: waiting for device to settle before scanning usb 4-2: USB disconnect, address 101 usb 4-3: USB disconnect, address 9 usb 4-3: new high speed USB device using ehci_hcd and address 102 usb 4-3: configuration #1 chosen from 1 choice scsi7 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 102 usb-storage: waiting for device to settle before scanning Vendor: IC25N040 Model: ATCS04-0 Rev: 0000 Type: Direct-Access ANSI SCSI revision: 00 usb-storage: device scan complete usb 4-3: USB disconnect, address 102 usb 4-3: new high speed USB device using ehci_hcd and address 103 usb 4-3: configuration #1 chosen from 1 choice scsi8 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 103 usb-storage: waiting for device to settle before scanning Vendor: Hitachi Model: HTS541616J9SA00 Rev: Type: Direct-Access ANSI SCSI revision: 02 usb-storage: device scan complete wifi0: stuck beacon; resetting (bmiss count 4)
Code:usb 4-3: configuration #1 chosen from 1 choice scsi5 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 9 usb-storage: waiting for device to settle before scanning Vendor: Hitachi Model: HTS541616J9SA00 Rev: Type: Direct-Access ANSI SCSI revision: 02 usb-storage: device scan complete
Code:ls /dev/[hs]d[a-z] ls command funktioniert irg. zur Zeit nicht... (anscheinend bin ich in einem anderen Modus, muss ich wohl zu Hause nochmals gucken...sry)
Ok das dmesg sieht ganz gut aus, und ehci scheint auch zu laufen, wenn du nicht selber was mit udev/hal herumgespielt hast denk ich mir das das in ordnung sein wird.
Das du ls /dev/[hs]d[a-z] nicht ausführen kannst macht mir eher sorgen. Das sollte als unprivilegiertester aller user auch noch hinhauen. Ich würd im moment eher auf ein Berechtigungproblem tippen. Was sagt:
Code:ls -alh / | grep dev
deinen username?Code:grep plugdev < /etc/group
Hallo, also ls Command funktioniert noch immer nicht und auch x-window hat eine Macke. Sprich der HDD Crash dürfte sich ordentlich auf die Debian Installation ausgewirkt haben.
cat Command erkennt er auch nicht mehr...
nbdeb:/# lsCode:ls -alh / | grep dev
Unter /usr/bin befindet sich schon einiges - jedoch kein lsCode:nbdeb:/# which ls -> nix :( nbdeb:/# echo $PATH /usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/bin/X11
Code:grep plugdev < /etc/group nbdeb:/# grep plugdev < /etc/group plugdev:x:46:chris
"Schaut wild aus, viel Glück!
Die Install kannst du kuebeln.
Wenn du reiserfs verwendest uu einen tree rebuild. Bei ext würd ich noch einen fs check ausprobieren bevors ans neu aufsetzen geht.
Zitat von MarcellusWenn du reiserfs verwendest uu einen tree rebuild. Bei ext würd ich noch einen fs check ausprobieren bevors ans neu aufsetzen geht.
overclockers.at v4.thecommunity
© all rights reserved by overclockers.at 2000-2025